Wropo logo
Lipp Tai Tai
Reklaami postitama
  1. Kodu
  2. Äri
  3. Tooted ja Varud
Pange tähele, et Wropo töötab klassifitseeritud reklaamide platvormina ega kontrolli reklaamijaid ega nende loendeid. Vaadake rohkem

Meil pole otseseid teadmisi oma kasutajate kohta ega kontrolli nende tegevust. Vältige raha ette saatmist inimestele, keda te ei tunne. Enne jätkamist kontrollige alati veebitehingutes ja kontrollige teavet. Vaata vähem

LDC-X200 Laser Wire Rod Bars Diameter Measuring System

Floria Liang Tooted ja Varud, Bangkok, IMG-0
Floria Liang Tooted ja Varud, Bangkok, IMG-1
Floria Liang Tooted ja Varud, Bangkok, IMG-2
Tõlge: Lipp ET Algne

Overview
The non-contact diameter measuring system, is mainly used in the measurement of the outer diameter of various wire rods, bars, wires and pipes. The system can detect the change of the diameter (outer diameter) of the measured object in real time under the high temperature state.

The working principle
The diameter measuring system takes the laser scanning method as an example. It adopts the probe imported from Japan, which can achieve2um accuracy at the range of 0.3~30mm. The acquisition frequency reaches 2000 times/second. The probe uses a self-excited infrared light source, which overcomes the measurement problem in dim environments.
It adopts the measurement method of pulse parallel light scanning, and has a strong ability to resist the jitter of the measured object. (As shown in Figure 1) Since the shaking frequency of the measured object is much smaller than the scanning frequency, when the measured object A moves in the shakeable area, the measurement result will be able to ensure its accuracy because the time it blocks the beam does not change.
Figure 1: Probe Scanning Radiation Area

The detection principle is as follows
Figure 2: Working Principle

First, the mold oscillator generates self-excited high-frequency pulses, which are sent to the comparator and the stepping servo motor respectively. The stepping servo motor drives the octahedral prism to rotate at a high speed, and reflects the infrared laser emitted by the laser generator to the convex lens A. It becomes parallel light, and then collects on the photosensitive element C through the convex lens B in the infrared receiving probe. The photosensitive element C converts this signal into a corresponding electrical signal and sends it to the other end of the comparator to compare with the original signal.
When there is no object to be measured in the measuring probe, the pulse signal at both ends of the comparator will be the same. Therefore, there is no difference output: when there is an object to be measured in the measuring probe, the photosensitive element C will output no pulse signal during the period of scanning through the object to be measured. Therefore, there will be a difference input for a period of time at both ends of the comparator, which corresponds to the diameter of the measured object. By calculating the oscillation period of the pulse and the length of the time slice without pulse, the diameter of the measured object can be known.

The composition and functions of the system
The system consists of the following main parts (as shown in Figure 1)
1. A measurement frame with four pairs of high-frequency laser scanning probes and non-contact infrared thermometers is installed
2. Four intelligent signal processors connected with four pairs of high frequency laser scanning probes
3. Cold air blowing system for cooling and cleaning the measuring frame
4. High-performance intelligent controller responsible for front-end data signal processing and network communication
5. Data processing and analysis system installed with industrial grade PC, monitor and printer

The technical indexes
Wuhan CenterRise M&C Engineering CO., Ltd.
more info, please contact
sales@whzfy.com
wuhancenterrise@gmail.com

Hind: ฿0
Telefon: 15727288019
Whatsapp: Mitte
Kategooria: Tooted ja Varud
Tüüp: Professionaal
Linn: Bangkok
Piirkond: Bangkok
Viide: TH-67B843BACE
Viimane värskendus: 1 aasta tagasi
Visiidid: 178
Floria Liang Avatar Bg

Floria Liang

Registreeritud 26. juuni 2024

Helistage kohe, et suhelda otse müüjaga.

Rohkem reklaame
ZSQ-T200 Online Surface Quality Inspection System for Continuously Cast Product CCD

1

ZSQ-T200 Online Surface Quality Inspection System for Continuously Cast Product CCD

฿0

Bangkok

Äri » Tooted ja Varud

Professionaal

1 aasta tagasi

MOC-K100 Mold Oscillation Online Monitoring System

3

MOC-K100 Mold Oscillation Online Monitoring System

฿0

Bangkok

Äri » Tooted ja Varud

Professionaal

1 aasta tagasi

MDC-K120 Electronic Type MDC-K160 Mechnical Slab Mold Taper Measuring Instrument

2

MDC-K120 Electronic Type MDC-K160 Mechnical Slab Mold Taper Measuring Instrument

฿0

Bangkok

Äri » Tooted ja Varud

Professionaal

1 aasta tagasi

CPL-N100 Square Billet Round Billet Mold Surface Detection

1

CPL-N100 Square Billet Round Billet Mold Surface Detection

฿0

Bangkok

Äri » Tooted ja Varud

Professionaal

1 aasta tagasi

MLC-V235 Continuous Casting Mold Level Control System

1

MLC-V235 Continuous Casting Mold Level Control System

฿0

Bangkok

Äri » Tooted ja Varud

Eraisik

1 aasta tagasi

CPC-D100 CPC Photoelectric Strip Automatic Center Position Control System

2

CPC-D100 CPC Photoelectric Strip Automatic Center Position Control System

฿0

Bangkok

Äri » Tooted ja Varud

Professionaal

1 aasta tagasi


Wropo logo
  • Linnad
  • Piirkonnad
  • Riigid
  • Privaatsuspoliitika
  • Tingimused
  • F.A.Q.
  • Hinnakujundus
  • Kontakt

Wropo töötab klassifitseeritud reklaamide platvormina. Me ei oma, ei halda ega taga ühtegi toodet ega teenuseid, mille on loetletud kolmandate osapoolte reklaamijate poolt.

© 2025 Wropo. Kõik õigused kaitstud.

Valige kategooria